Metacomp FAQ/Solution Re-interpolator
From CFD-Wiki
m (Solution Re-interpolator moved to Metacomp FAQ/Solution Re-interpolator: More correct title) |
|||
| (6 intermediate revisions not shown) | |||
| Line 3: | Line 3: | ||
=== What is it? === | === What is it? === | ||
| - | + | This tool is a solution re-interpolator, which is intended to take the solution on an existing mesh and interpolate that solution to a new mesh. Cell centroids in the new mesh which lie outside the domain of the old grid are initialized by marching data from interior cells that were successfully interpolated. | |
=== When should I use it? === | === When should I use it? === | ||
| - | This tool can be used when you wish to transfer the existing solution from one mesh (old) to a another mesh (new). The old and new meshes must have the same geometry but can have a different number of distribution of grid points. This tool is especially handy if you want to perform a grid convergence study on three meshes, say a course, medium and fine mesh. The solution from course mesh could be interpolated onto the medium mesh then from the medium mesh to the fine mesh in order to significantly reduce the convergence time. | + | This tool can be used when you wish to transfer the existing solution from one mesh (old) to a another mesh (new). The old and new meshes must have the same geometry in general but can have a different number of distribution of grid points. This tool is especially handy if you want to perform a grid convergence study on three meshes, say a course, medium and fine mesh. The solution from course mesh could be interpolated onto the medium mesh then from the medium mesh to the fine mesh in order to significantly reduce the convergence time. |
| - | == | + | == Running from the GUI == |
| - | === | + | === Preparation Steps === |
| + | |||
| + | In order to make things clear we will establish a naming convention. We will call the existing solution, the one we are interpolating FROM, the OLD solution. We therefore call the solution we are interpolating TO, the NEW solution. | ||
| + | |||
| + | 1. First rename the following files in the NEW solution folder: | ||
| + | |||
| + | ''cellsin.bin'' -------> ''new_cellsin.bin'' | ||
| + | ''nodesin.bin'' -------> ''new_nodesin.bin'' | ||
| + | |||
| + | 2. Copy theses two files from the NEW solution folder to the OLD solution folder | ||
| + | |||
| + | === Running the Tool === | ||
To initiate the tool from the GUI go to Tools -> CFD++ Solution Tools -> Solution Re-interpolator. The following window will appear: | To initiate the tool from the GUI go to Tools -> CFD++ Solution Tools -> Solution Re-interpolator. The following window will appear: | ||
| Line 18: | Line 29: | ||
[[Image:reintsom.png]] | [[Image:reintsom.png]] | ||
| - | |||
| - | + | 3. Leave the default values and select the "Run Tool" button to start the run. | |
| + | |||
| + | === Post Run Steps === | ||
| + | |||
| + | 4. Copy the ''new_cdepsout.bin'' file from the OLD solution folder to the NEW solution folder. | ||
| + | |||
| + | 5. Remove the ''new_'' appendage from each of the following files: | ||
| + | |||
| + | ''new_cellsin.bin'' | ||
| + | ''new_nodesin.bin'' | ||
| + | ''new_cdepsout.bin'' | ||
| + | |||
| + | == Running from the Command Line == | ||
| + | |||
| + | === Preparations Steps === | ||
| + | |||
| + | The preparation steps are identical to steps 1-2 above. | ||
| + | |||
| + | === Running the Tool === | ||
| + | |||
| + | Use the following command | ||
| + | |||
| + | ''reintsom new_cellsin.bin new_nodesin.bin new_cdepsout.bin cdepsout.bin'' | ||
| + | |||
| + | === Post Run Steps === | ||
| + | |||
| + | The post run steps are identical to steps 4-5 above. | ||
Latest revision as of 08:05, 26 April 2009
Contents |
Introduction
What is it?
This tool is a solution re-interpolator, which is intended to take the solution on an existing mesh and interpolate that solution to a new mesh. Cell centroids in the new mesh which lie outside the domain of the old grid are initialized by marching data from interior cells that were successfully interpolated.
When should I use it?
This tool can be used when you wish to transfer the existing solution from one mesh (old) to a another mesh (new). The old and new meshes must have the same geometry in general but can have a different number of distribution of grid points. This tool is especially handy if you want to perform a grid convergence study on three meshes, say a course, medium and fine mesh. The solution from course mesh could be interpolated onto the medium mesh then from the medium mesh to the fine mesh in order to significantly reduce the convergence time.
Running from the GUI
Preparation Steps
In order to make things clear we will establish a naming convention. We will call the existing solution, the one we are interpolating FROM, the OLD solution. We therefore call the solution we are interpolating TO, the NEW solution.
1. First rename the following files in the NEW solution folder:
cellsin.bin -------> new_cellsin.bin nodesin.bin -------> new_nodesin.bin
2. Copy theses two files from the NEW solution folder to the OLD solution folder
Running the Tool
To initiate the tool from the GUI go to Tools -> CFD++ Solution Tools -> Solution Re-interpolator. The following window will appear:
3. Leave the default values and select the "Run Tool" button to start the run.
Post Run Steps
4. Copy the new_cdepsout.bin file from the OLD solution folder to the NEW solution folder.
5. Remove the new_ appendage from each of the following files:
new_cellsin.bin new_nodesin.bin new_cdepsout.bin
Running from the Command Line
Preparations Steps
The preparation steps are identical to steps 1-2 above.
Running the Tool
Use the following command
reintsom new_cellsin.bin new_nodesin.bin new_cdepsout.bin cdepsout.bin
Post Run Steps
The post run steps are identical to steps 4-5 above.
